For parts wholesalers, importers, and engine rebuilders, an unmarked sample valve without an OE number does not have to stall a purchase order. While sending an existing part number is always the fastest way to quote, experienced engine valve manufacturers can match catalog stock—or tool up custom replacement batches—using five simple bench measurements, stem coating checks, and the engine code.
Whether your customer mailed a worn core sample in a box or you are cross-referencing dead stock from an old warehouse batch, this guide shows your sourcing team how to measure, verify, and quote unmarked engine valves accurately without risking expensive container returns.
Check Three Places Before Measuring an Unmarked Sample
Before setting up micrometers, inspect the sample batch closely for three factory clues buyers often overlook. Wipe the upper-middle section of the valve stem with solvent, because many factories laser-etch short batch codes or OE prefixes on the section shielded inside the oil seal.
If the metal itself is clean, check old supplier packing lists, past purchase orders, or electronic parts catalogs by the buyer's engine build code—see our OE number & valve cross-reference guide for matching trade catalog numbers. Confirming a reference number upfront tells your engine valve supplier right away whether the batch requires special construction, such as hollow sodium-cooled stems for turbo engines.
The 5 Measurements Every Engine Valve Supplier Needs
When no catalog number exists, five core dimensions let a manufacturer cross-check stock molds or prepare an engineering drawing. Use digital calipers for head width and overall length, and check the stem with a 0.01 mm (0.0004 in) outside micrometer—standard calipers can easily misread a round shaft by 0.05 mm (0.002 in), leading to wrong-fit bulk shipments.
1. Head Diameter (Width Across the Combustion Face)
Measure straight across the widest flat rim of the valve head. Across passenger cars, pickups, and commercial diesels, most aftermarket engine valves fall between 20 and 60 mm (0.79 and 2.36 in) in head diameter.
Always pick the cleanest intact sample from the batch before recording this size. Carbon burn-off, edge chipping, or prior shop refacing can shave 0.3 to 0.5 mm (0.012 to 0.020 in) off a used valve head and distort your target dimension.
2. Stem Diameter (Thickness Along the Unworn Shaft)
Clean off baked oil varnish and check stem thickness in three spots: right below the keeper grooves, mid-shaft, and near the head transition. Standard automotive and heavy-duty diesel valve stems measure 4 to 14 mm (0.157 and 0.551 in).
Always report the reading closest to the keeper grooves. High-mileage samples wear slightly thinner in the center where they rub the valve guide, making a standard 6.00 mm (0.236 in) shaft measure 5.94 mm if you only gauge the middle.
3. Overall Length (Flat Face to Stem Tip)
Measure from the flat face of the valve head straight to the very top of the stem tip. Production valves typically run between 60 and 240 mm (2.36 and 9.45 in) end to end.
Check the flat tip for mushrooming or prior machining marks before quoting. If a machine shop previously ground the tip shorter during an older overhaul, flag that on your RFQ so the factory builds to the original OE length rather than copying a worn sample.
4. Keeper Grooves and Tip-to-Groove Height
Count the locking grooves near the stem tip—most high-volume applications use one square groove, one round bead groove, or three multi-bead grooves. Also measure from the flat tip down to the top edge of the first groove.
Matching only the groove count is a common sourcing mistake. Under SAE J775 engine poppet valve guidelines, a 1.0 mm (0.039 in) error in tip-to-groove position shifts valve spring preload and can cause retainers to pop loose under high load.
5. Seat Face Angle (Plus Stem Finish Check)
Verify the beveled sealing edge with a protractor: most production valves use a 45° seat angle, while select diesel and high-flow intakes use a 30° angle. Be clear on quotes—North American specs list the 45° seat angle, while many Asian and European factory prints list the 90° included cone angle across both sides.
Also note the stem finish on your sample, such as bright hard chrome plating or dark matte nitride coating. You can review how factories apply these wear layers in our overview of the engine valve manufacturing process so your replacement lot matches original service life.
| Dimension to Record | Bench Tool | Standard Production Range | B2B Sourcing Pitfall to Avoid |
|---|---|---|---|
| 1. Head Diameter | Digital Caliper | 20 – 60 mm (0.79 – 2.36 in) | Measuring burned or previously reground valve heads. |
| 2. Stem Diameter | Outside Micrometer (0.01 mm / 0.0004 in) |
4 – 14 mm (0.157 – 0.551 in) | Measuring only the worn mid-shaft with loose calipers. |
| 3. Overall Length | Digital Caliper | 60 – 240 mm (2.36 – 9.45 in) | Copying a tip that was ground shorter in a past rebuild. |
| 4. Keeper Grooves | Caliper + Close-up Photo | 1 square, 1 round, or 3-bead | Noting groove count without tip-to-groove distance. |
| 5. Seat Angle | Bevel Gauge / Protractor | 45° or 30° seat (90° or 120° cone) | Confusing single-side seat angle (45°) with cone angle (90°). |
How to Tell Intake from Exhaust Before Placing an Order
Mixing up intake and exhaust quantities on a purchase order creates costly warranty disputes, especially when partnering with a separate intake valve supplier or exhaust valve supplier. Put matched samples from the same cylinder side by side: intake valves almost always have heads 3 to 6 mm (0.12 to 0.24 in) wider to bring air into the cylinder.
When head diameters look almost identical on older commercial diesels, use a pocket magnet to verify construction:
Intake valves are magnetic from tip to head. Running cooler at 250°C to 300°C (482°F to 572°F), they are forged from durable martensitic alloy steel.
Bi-metal exhaust valve heads show little or no magnetic pull. Because exhaust valves face 750°C to 850°C (1,382°F to 1,562°F) heat, factories join a non-magnetic heat-resistant head to a magnetic stem tip using friction welding for bimetallic engine valves.
Understanding these material splits—covered further in our intake vs. exhaust valve guide—ensures you quote heat-resistant exhaust alloys rather than ordering intake steel by mistake.
| Bench Check | Engine Intake Valve | Exhaust Valve |
|---|---|---|
| Head Diameter | Wider—typically 3 – 6 mm (0.12 – 0.24 in) larger | Smaller, often with a thicker outer margin band |
| Magnet Test | Magnetic on both head and stem | Non-magnetic (or very weak) on head; magnetic on stem tip |
| Weld Line & Duty | Usually one-piece mono-metal alloy (250–300°C / 482–572°F) | Two-piece friction-welded alloy (750–850°C / 1,382–1,562°F) |
| Typical Stem Finish | Hard chrome plating or polished stem | Hard chrome plating or liquid nitride coating on diesels |
Common Engine Valve Quick Reference (Dimensions & OE Numbers)
Use this cross-reference table of high-volume passenger, pickup, and commercial diesel applications to match measured bench dimensions against known OE part numbers before submitting a wholesale inquiry:
| Engine Platform | Typical Vehicles | Position | Head × Stem × Length | Angle | Verified OE Reference |
|---|---|---|---|---|---|
| VW / Audi 2.0 TSI (EA888) | Golf GTI, Passat, Tiguan, Audi A4/Q5 | Intake Exhaust |
34.0 × 6.0 × 103.9 mm (1.339 × 0.236 × 4.091 in) 28.0 × 6.0 × 101.8 mm (1.102 × 0.236 × 4.008 in) |
45° | 06D109601M / 06D109611H(see EA888 guide) |
| VW 1.9D / Santana | VW Santana 2000, Transporter | Intake Exhaust |
36.0 × 7.0 × 97.0 mm (1.417 × 0.276 × 3.819 in) 32.0 × 7.0 × 96.0 mm (1.260 × 0.276 × 3.780 in) |
45° | 028 109 601 J / 028 109 611 K |
| Peugeot 1.6 (EP6CDTM) | Peugeot 207 / 308 1.6T | Intake | 29.1 × 5.0 × 95.1 mm (1.146 × 0.197 × 3.744 in) | 45° | 0948.G |
| Toyota 2TR-FE (2.7L Gas) | Hilux, HiAce, Land Cruiser Prado | Intake Exhaust |
37.5 × 5.5 × 102.2 mm (1.476 × 0.217 × 4.024 in) 30.5 × 5.5 × 100.6 mm (1.201 × 0.217 × 3.961 in) |
45° | 13711-75110 / 13715-75100(see Toyota guide) |
| Toyota 1KD-FTV (3.0L Diesel) | Hilux, Prado, HiAce Diesel | Intake Exhaust |
32.5 × 6.0 × 103.5 mm (1.280 × 0.236 × 4.075 in) 28.5 × 6.0 × 103.4 mm (1.122 × 0.236 × 4.071 in) |
45° | 13711-30030 / 13715-30030 |
| Toyota 1ZR / 2ZR (1.6–1.8L) | Corolla, Auris, Levin | Intake Exhaust |
31.9 × 5.5 × 106.8 mm (1.256 × 0.217 × 4.205 in) 27.4 × 5.5 × 108.4 mm (1.079 × 0.217 × 4.268 in) |
45° | 13711-37020 / 13715-37030 |
| Cummins ISF 2.8L (Diesel) | Foton Light Truck, GAZelle Van | Intake Exhaust |
34.0 × 7.0 × 114.5 mm (1.339 × 0.276 × 4.508 in) 31.0 × 7.0 × 114.5 mm (1.220 × 0.276 × 4.508 in) |
45° | 5261320 / 5256949 |
Note: Always verify keeper groove count, tip-to-groove height, and engine block code before finalizing wholesale purchase orders.
Verifying Kit Quantities (8V, 12V, and 16V Configurations)
Packaging errors often happen when buyers misread engine-family badges on purchase requests. A label like 8V, 12V, or 16V always lists the total number of valves per complete engine kit, not per cylinder.
Most 16-valve passenger platforms—like the DOHC four-cylinders covered in our 16-valve engine buyers' check and Nissan Twin Cam 16V application guide—require 8 intake valves and 8 exhaust valves per full set. However, an older pushrod V8 with 2 valves per cylinder also uses 16 valves total, so always confirm cylinder count before locking kit packaging BOMs.
Why Engine Codes Beat Vehicle Model Years on Bulk RFQs
Sourcing solely by vehicle name and year—such as "2008 VW 1.9 diesel" or "Citroën 1.6"—is the #1 cause of mismatched stock shipments. Automakers routinely adjust valve stem diameters, groove counts, and seat angles mid-production without changing exterior trim badges.
For instance, VW's 028 109 601 1.9 diesel family splits between 8.0 mm (0.315 in) and 7.0 mm (0.276 in) stems, while Citroën's 0948.65 1.6L intake exists in both 30° and 45° seat faces. Recording the stamped block code prevents cross-reference errors on high-demand engines (if you are deciding between chassis records and block stamps, read our guide on ordering parts by VIN vs. engine code), whether sourcing Toyota pickup valves (1KD vs. 2KD vs. 2TR-FE) or Gen 2 vs. Gen 3 VW & Audi EA888 valves.
How to Submit Samples & Specs to TOPU for Wholesale or Custom Manufacturing
As an IATF 16949:2016 certified OEM & aftermarket supplier—learn more about our quality vetting checklist in how to choose an OEM engine valve manufacturer and our guide on sourcing automotive engine valves from China—TOPU turns physical samples or CAD prints into repeatable bulk batches.
To receive accurate cross-reference confirmation, pricing, and MOQ/lead times on your first email, include four items in your RFQ:
Bench photos with scale: Full profile alongside a millimeter scale, plus a sharp close-up of the keeper grooves and stem tip.
All 5 measurements & finish: Head diameter, unworn stem diameter, overall length, groove type + tip-to-groove distance, seat angle (45° or 30°), and coating (hard chrome plating or nitride).
Engine code & fuel type: Block code, market/year, and duty cycle (gasoline, turbo-diesel, or dry-burning CNG/LPG requiring Stellite-faced seats).
Order volume & companion components: Target order quantity, custom box/laser marking needs, and any matching hydraulic or mechanical valve tappets required for full cylinder head overhaul kits (physical samples can also be shipped directly to our metrology lab for reverse-engineering).
Frequently Asked Questions
How can I measure the size of an engine valve?
Clean an undamaged sample and measure five specs: check head width and overall length with digital calipers, gauge unworn stem diameter near the keeper grooves with a 0.01 mm (0.0004 in) outside micrometer, count the keeper grooves plus tip-to-groove height, and verify the 45° or 30° seat angle with a protractor.
How do you tell which valve is intake or exhaust?
Place matched valves from the same cylinder side by side: the engine intake valve almost always has a wider head by 3 to 6 mm (0.12 to 0.24 in). Confirm metallurgy with a magnet—intake heads pull strongly on a magnet, while friction-welded bi-metal exhaust heads show virtually zero pull.
Does 16 valve mean 4 cylinders?
Most often yes—a "16V" label typically indicates a 4-cylinder DOHC engine with 4 valves per cylinder (8 intake + 8 exhaust per full engine kit). However, "16-valve" always expresses total valve count, meaning a 2-valve-per-cylinder V8 also totals 16 valves, so always confirm cylinder count before finalizing bulk kit BOMs.
Request a Wholesale Match or Custom Production Quote
Looking for an experienced engine valve manufacturer for aftermarket distribution, fleet rebuilding programs, or discontinued OEM replacements by sample? Send your 5 measurements, sample photos, or engine codes—our engineering desk will cross-check our 20–60 mm (0.79–2.36 in) catalog and reply within 24 hours with stock availability, custom tooling lead times, and direct factory pricing for engine valves and valve tappets.
📧 Email: [email protected]
📱 Tel / WhatsApp: +86 138 6266 4011
🌐 Website: www.e-topu.com